FREE SHIPPING ON ORDERS OVER $350 (USA ONLY - SOME EXCLUSIONS APPLY) | 877-4-SPRUCE
Thumbs 1
Thumbs 1
Thumbs 1

2 Hole Surface Mounted Mic & Phone Jack Housing

Select Model:
BlackBeigeAluminum
Quantity
Add to Wishlist

Overview

Metal housing available in Powdercoat finish, 2-hole .380 w/key, can be used on mic & phone jacks, intercoms, fuses, switches etc. Can mount with (4) small screws on outer flange.
(Flange NOT predrilled & hardware NOT included)
Powdercoat finish Aluminum .040
Dimensions W 2.9" X L 3.56" to outer edge of flange X H 1.06
Outer flange 1/4"
Holes .380 dia x 1.0 between centers
  • Frequently Purchased With
  • Customers Also Viewed

Reviews

Liked what I got. One critique, the holes didn’t match the jacks and had to up size them.

Craig E Verified Purchase

SURF MTD MIC & PHN JACK HS BLK

November 8, 2023

This is a metal box. Be sure to use insulation washers with it.

Kenneth H Verified Purchase

SURF MTD MIC & PHN JACK HS BLK

June 4, 2023

Magaero L Verified Purchase

SURF MTD MIC & PHN JACK HS BLK

April 27, 2023

Aya A Verified Purchase

SURF MTD MIC & PHN JACK HS BLK

September 8, 2022

Good hardware. Nothing cheesy. I thought the price was very reasonable. Bought four of them. 👍🏽

Chris P Verified Purchase

SURF MTD MIC & PHN JACK HS BLK

February 27, 2022

Used on outside of side panels. Tried recessing but too hard to plug-in. Very good quality

Michael S Verified Purchase

SURF MTD MIC & PHN JACK HS BEI

December 11, 2021

Was supposed to be finished but came bare aluminum.

William H Verified Purchase

SURF MTD MIC & PHN JACK HS ALM

November 12, 2021

These are ideal for mounting mic and audio jacks, either surface mounted or recessed. First off, enlarge the jack holes if necessary, with a correctly sized step drill. If you find that the angle of the installed jack will not allow the plug to be inserted, simply use a punch, inserted into the jack, to slightly bend the jack outward to allow the plug to be inserted without interference. When surface mounting, a hole large enough to insert a jack, must be drilled. This will be hidden when the housing is attached to the panel. If you flush mount the housing, cut a square hole in the panel, JUST large enough to allow the body of the housing to drop in, leaving the rim of the housing on the surface of the panel. These are extremely handy items due to their versatility. Just have to use some imagination.

Web
May 10, 2020

Quality material, and great price.

Cindy
November 14, 2019

I am not sure about the other low reviews on this product. Put in one two-jack and one four-jack in the back of a cabin Waco for a PS 3000 system. Jacks fit perfect and easy to install. Bought the aluminum one and powder coated to match. NO issues.

Neal G
November 3, 2018

Q&A

Please note, Aircraft Spruce's personnel are not certified aircraft mechanics and can only provide general support and ideas, which should not be relied upon or implemented in lieu of consulting an A&P or other qualified technician. Aircraft Spruce assumes no responsibility or liability for any issue or problem which may arise from any repair, modification or other work done from this knowledge base. Any product eligibility information provided here is based on general application guides and we recommend always referring to your specific aircraft parts manual, the parts manufacturer or consulting with a qualified mechanic.

Q: On the beige model, are both sides powder coated?

Yes, both sides are powder coated.

Q: 10-01595 Does the surface with the hole cutouts sit at right angle to the flanged mounting surface, or at some other angle. Reason is I would not want jacks to angle too far away from the mounting surface, if that makes any sense ?

They are slightly less than a 90 degree angle.

View in Catalog

View Image View in Catalog